Findapart

Cheap Škoda Yeti Drive Shaft

Need a used Škoda Yeti drive shaft? Request a free quote from UK vehicle dismantlers and compare offers direct.

Enter your registration or select your vehicle

Find the right part faster and get quotes direct from UK breakers - free, and no obligation.

GB

A buyer's guide to used Škoda Yeti drive shaft

No two drive shafts are quite the same across different vehicles, so getting the specifics right matters when you buy used, second hand or a replacement. Answer a few quick questions below and breakers will only quote if they have the exact matching part in stock:

Also known as: half shaft, driveshaft, prop shaft.

Other used Škoda Yeti parts

Used drive shaft for other Škoda models

Fitment questions

Will a drive shaft from an earlier Škoda Yeti fit my newer one?

The Škoda Yeti ran as a single generation from 2009 to 2017, with a facelift in 2013, so there is a meaningful mid-life boundary to be aware of. Drive shaft fitment is governed primarily by engine code and gearbox type rather than model year alone, but ancillary or mounting changes can occur across a facelift year, so confirm with the breaker against your registration whether a pre-2013 shaft crosses cleanly to a post-2013 car. Supply your engine code from your V5 or a VIN check — that single detail is more useful to the breaker than the year badge.

Does the engine code really matter for a Yeti drive shaft, or is the year enough?

Engine code matters above everything else for a drive shaft — two Yetis from the same year can use completely different shafts if they carry different engines or gearboxes. The Yeti was offered with a range of petrol and diesel units across its 2009–2017 run, and shaft length, spline count, and CV joint design follow the drivetrain, not the calendar. Find your engine code on your V5 logbook or a VIN check and give it to the breaker; it is the single most useful detail you can supply.

Does it matter whether I have the Yeti S, SE, Elegance, or Laurin & Klement trim when sourcing a drive shaft?

Trim level — whether S, SE, Elegance, or Laurin & Klement — does not affect drive shaft fitment; the shaft follows the engine code, fuel type, and gearbox type, not the badge on the tailgate. A shaft pulled from an SE and one from a Laurin & Klement with the same engine and gearbox combination are mechanically interchangeable. The only differences you might notice between trim-level donor cars are cosmetic ones such as alloy wheels or interior finish, which are irrelevant to the drivetrain part you need.

Do I need a different drive shaft for a 4x4 Yeti compared to a front-wheel-drive one?

Yes, this is one of the most important distinctions for the Yeti — a four-wheel-drive car has an additional rear drive shaft arrangement and different front shaft geometry to a front-wheel-drive model, so the parts are not interchangeable between the two layouts. Always confirm with your breaker whether the donor vehicle matches your exact drivetrain configuration as well as your engine code. Supplying your full engine code and stating whether your car is 4WD or FWD will allow the breaker to identify the correct shaft quickly.

I have a 2012 Yeti — will a drive shaft from a 2014 post-facelift Yeti fit it?

Your 2012 car is a pre-facelift Yeti and the 2014 car sits after the 2013 facelift, which means you are crossing a production boundary where fitment cannot be assumed to be direct without checking. Engine code and gearbox type remain the primary fitment factors, but mounting or ancillary changes can occur across a facelift, so you should confirm compatibility with the breaker against both registrations rather than relying on the part looking similar. Give the breaker both engine codes and let them cross-reference before purchasing.

Does a petrol Yeti drive shaft fit a diesel Yeti of the same year?

Not necessarily — fuel type determines which engine is fitted, and different engines are matched to different gearboxes and drivetrain configurations, all of which influence shaft specification. A petrol and a diesel Yeti from the same year could have shafts that differ in length, spline count, or CV joint design. Always match on engine code and gearbox type, not just fuel type or year, and confirm with the breaker against your registration to be sure.