Findapart

Cheap Škoda Kamiq Exhaust Manifold

Get quotes for a used or replacement Škoda Kamiq exhaust manifold. Genuine second hand parts from UK vehicle dismantlers - free request, breakers with stock reply direct.

Enter your registration or select your vehicle

Find the right part faster and get quotes direct from UK breakers - free, and no obligation.

GB

A buyer's guide to used Škoda Kamiq exhaust manifold

No two exhaust manifolds are quite the same across different vehicles, so getting the specifics right matters when you buy used, second hand or a replacement. Answer a few quick questions below and breakers will only quote if they have the exact matching part in stock:

Other used Škoda Kamiq parts

Used exhaust manifold for other Škoda models

Fitment questions

Does the Škoda Kamiq actually have an exhaust manifold?

Yes, every Škoda Kamiq has an exhaust manifold — it is the cast component that collects exhaust gases from each cylinder and routes them into the rest of the exhaust system. On the Kamiq, which launched in the UK in 2019 and uses only turbocharged petrol and diesel engines, the manifold is typically integrated into or mounted very close to the turbocharger assembly, so you may see it listed alongside turbo-related parts. All variants have one, but the design differs between engine types, so you need to match on engine code rather than year or trim alone.

Will a Kamiq exhaust manifold from a 2019 or 2020 car fit my 2022 or newer Kamiq?

The Kamiq received a facelift in 2021, but the core engine family — including the 1.0 TSI and 1.5 TSI petrol units and the 1.6 TDI diesel — carried over largely unchanged across the pre- and post-facelift cars. If the engine code on the donor car matches yours exactly, fitment is likely, but because the 2021 facelift is a genuine generation boundary, you should confirm with the breaker that the manifold from a pre-facelift car matches your specific engine code before buying. Never assume year-to-year compatibility without checking the code.

Does the trim level affect which exhaust manifold I need — for example, does an S, SE, SE L or Monte Carlo Kamiq use a different one?

Trim level has no bearing on exhaust manifold fitment — the S, SE, SE L, and Monte Carlo all use the same manifold for a given engine, because trim differences are cosmetic and equipment-based, not mechanical. What you will find is that Monte Carlo and SE L models were more commonly paired with the 1.5 TSI engine, so if you are sourcing from a breaker, just confirm the engine code matches yours rather than worrying about which trim the donor car was. A manifold from a base-spec S model with the same engine code is equally valid.

Does fuel type matter when sourcing a used Kamiq exhaust manifold?

Yes, petrol and diesel exhaust manifolds are completely different parts and will not interchange — a 1.6 TDI manifold will not fit a 1.0 TSI or 1.5 TSI, and vice versa. Within the petrol range, the 1.0 TSI three-cylinder and 1.5 TSI four-cylinder also have different manifolds, so matching on the full engine code stamped on your block is essential. Always give the breaker your registration and engine code so they can pull the correct part.

Does the emissions standard (Euro 6) affect which exhaust manifold fits my Kamiq?

The Kamiq launched after Euro 6 was already mandatory for new cars in the UK, so all UK-market Kamiqs are Euro 6 vehicles and this is less of a concern than it would be on an older model that spanned Euro 5 and Euro 6 production. However, if a breaker is offering a manifold from a European-market Kamiq or a related platform vehicle, emissions-era differences could affect how downstream components connect, so it is worth confirming the part came from a UK or Euro 6-compliant car. If you have any doubt, ask the breaker to verify against your registration plate.

My Kamiq needs an exhaust manifold and a new catalytic converter — can I source both from the same donor car?

Sourcing both from the same donor car with the same engine code is a sensible approach, since they are designed to work together and the joints and flanges are more likely to align correctly. However, whether a specific cat or DPF unit from a breaker will pass MOT emissions testing on your car depends on factors including your car's exact calibration and the condition of the donor unit — this is strong confirm-with-breaker territory and not something that can be guaranteed in advance. Ask the breaker explicitly about the emissions compliance of any catalytic converter or DPF they supply alongside the manifold.