Findapart

Second Hand Škoda Enyaq AC Compressor

Get quotes for a used or replacement Škoda Enyaq ac compressor. Genuine second hand parts from UK vehicle dismantlers - free request, breakers with stock reply direct.

Enter your registration or select your vehicle

Find the right part faster and get quotes direct from UK breakers - free, and no obligation.

GB

A buyer's guide to used Škoda Enyaq ac compressor

No two ac compressors are quite the same across different vehicles, so getting the specifics right matters when you buy used, second hand or a replacement. Answer a few quick questions below and breakers will only quote if they have the exact matching part in stock:

Other used Škoda Enyaq parts

Used ac compressor for other Škoda models

Fitment questions

Will an AC compressor from an earlier Škoda Enyaq fit my newer one?

The Enyaq has been built on the MEB electric platform since its 2021 UK launch, and a mid-cycle refresh arrived for the 2024 model year, so there is a facelift boundary to be aware of. For pre-facelift (2021–2023) to facelift (2024 onwards) swaps, the core drivetrain architecture is shared, but ancillary mounting and connector changes around that 2024 boundary mean you should confirm directly with the breaker against your registration before buying. Your most useful information to give a breaker is your full VIN or registration, which will pin down the exact build spec.

Does the engine code matter for an Enyaq AC compressor if it's fully electric?

Yes — on an EV the 'engine code' equivalent is the motor and inverter code stamped in your V5 or retrievable via a VIN check, and this determines which compressor variant was fitted at the factory. The Enyaq is available in rear-wheel-drive single-motor variants and all-wheel-drive dual-motor variants (such as the iV 80x and RS iV), and the compressor spec can differ between these drivetrains. Always supply your motor code or at minimum your exact model variant (e.g. 60, 80, 80x, RS) when requesting a quote from a breaker.

Does it matter which trim level my Enyaq is — will a compressor from a Loft or Sportline fit my Suite or RS?

For the AC compressor specifically, trim level does not affect fitment — the Enyaq's trim grades (which include Loft, Sportline, Suite, and RS iV) share the same mechanical HVAC compressor for a given motor variant. What can differ between trims is surrounding interior and underbonnet dressing, so a used compressor from a lower trim may look slightly different cosmetically in terms of brackets or looms, but the core unit follows the drivetrain, not the badge. Confirm the motor variant matches and check with the breaker that no ancillary differences apply to your specific registration.

Is a compressor from a 2022 Enyaq 80 compatible with my 2024 Enyaq 80?

This question crosses the 2024 facelift boundary, which is the key dividing line in Enyaq production, and while the underlying MEB platform is continuous, ancillary and mounting changes can occur at a facelift without being widely documented. We would not state this as a confirmed interchange — route this question directly to your breaker, giving them both the donor registration and your own, so they can check part numbers against both vehicles. Supplying your VIN will give the breaker the most accurate picture.

Can I use an Enyaq AC compressor from any year if my car is under warranty or has a heat pump fitted?

Some Enyaq variants were offered with an optional heat pump system, which integrates with the refrigerant circuit and means the compressor specification may differ from non-heat-pump cars even within the same model year. Whether a used compressor will work correctly with your heat pump setup, and any implications for recoding or pairing with the vehicle's thermal management ECU, are things you must confirm with the breaker and ideally a specialist EV technician. Always tell the breaker whether your car has the heat pump option when requesting a quote.

Do I need to worry about ECU pairing or coding when fitting a used Enyaq AC compressor?

This is a genuine concern on modern EVs, as some compressor assemblies contain control electronics that may need to be configured to the receiving vehicle. We cannot state as fact exactly which Enyaq compressor variants require coding and which are plug-and-play, so this must be confirmed with the breaker against your specific registration. A breaker who specialises in MEB-platform vehicles will be best placed to advise, and you should factor potential coding costs into your budget before purchasing.