Second Hand Mazda CX-3 Washer Motor
Need a used Mazda CX-3 washer motor? Request a free quote from UK vehicle dismantlers and compare offers direct.
Enter your registration or select your vehicle
Find the right part faster and get quotes direct from UK breakers - free, and no obligation.
Choosing the right used Mazda CX-3 washer motor
Used washer motors vary between vehicles - and whether you call it used, second hand or a replacement, matching the right one matters. These are the details breakers need to match the right part to your car - our request form asks them so you only hear from suppliers with the correct part:
- State whether you need front only or front and rear
Other used Mazda CX-3 parts
- Used Mazda CX-3 Body Control Module
- Used Mazda CX-3 Fuse Box
- Used Mazda CX-3 Horn
- Used Mazda CX-3 Aerial
- Used Mazda CX-3 Bonnet
- Used Mazda CX-3 Airbag Control Module
- Used Mazda CX-3 Boot Lid
- Used Mazda CX-3 EGR Valve
- Used Mazda CX-3 Bonnet Strut
- Used Mazda CX-3 Drive Shaft
- Used Mazda CX-3 Steering Box
- Used Mazda CX-3 Power Steering Pump
Used washer motor for other Mazda models
Fitment questions
Does the Mazda CX-3 have a washer motor, and where is it located?
Yes, the Mazda CX-3 has a washer motor — in fact it typically has two: one for the front windscreen washers and one for the rear. They are usually mounted on or near the washer fluid reservoir, which is located in the engine bay on the nearside. Both motors are standard fitment across all CX-3 variants regardless of engine or trim level.
Will a washer motor from a 2016 CX-3 fit my 2019 CX-3?
The Mazda CX-3 first generation ran from 2015 through to 2023 with a facelift introduced around 2018, so both a 2016 and a 2019 car sit either side of that facelift boundary. The fundamental reservoir and motor setup may well be the same, but whether the connector and mounting are identical across the facelift is something you should confirm with the breaker against your registration before buying.
Does the trim level affect which washer motor I need — for example, does a Sport Nav motor fit a SE-L Nav CX-3?
Trim level does not affect which washer motor is fitted to the CX-3 — the same motors are used across SE, Sport, Sport Nav, SE-L Nav and GT Sport trims. You may find minor cosmetic differences around the washer jet nozzles on the bonnet depending on trim, but the motor itself is interchangeable. Give the breaker your registration to confirm the part number matches, and you should be fine.
Is the front washer motor the same part as the rear washer motor on the CX-3?
No, they are different parts — the front and rear washer motors are separate units with different flow rates and sometimes different connectors, even though they may sit on the same reservoir. When contacting a breaker, make sure you specify whether you need the front or rear motor to avoid being sent the wrong one.
Can I use a washer motor from another Mazda model on my CX-3?
It is possible that Mazda shares washer motor components across models such as the Mazda 2, Mazda 3, or CX-5, as manufacturers commonly use the same reservoir and motor assemblies across a platform range. However, confirming cross-model compatibility is not straightforward without checking part numbers, so ask the breaker to match it against your CX-3's registration rather than assuming it will fit.
My CX-3 washers have stopped working — how do I know if it's the motor that needs replacing?
If you can hear a hum or clicking when you activate the washers but no fluid comes out, the motor may be seized or faulty; if there is complete silence, the motor or its fuse is the likely culprit. A breaker selling a used washer motor cannot guarantee the unit is fault-free, so it is worth asking whether they have bench-tested it or can offer any short-term warranty. If in doubt, have a mechanic confirm the diagnosis before ordering a replacement part.