Cheap Mazda Premacy Bumper
Get quotes for a used or replacement Mazda Premacy bumper. Genuine second hand parts from UK vehicle dismantlers - free request, breakers with stock reply direct.
Enter your registration or select your vehicle
Find the right part faster and get quotes direct from UK breakers - free, and no obligation.
A buyer's guide to used Mazda Premacy bumper
No two bumpers are quite the same across different vehicles, so getting the specifics right matters when you buy used, second hand or a replacement. Answer a few quick questions below and breakers will only quote if they have the exact matching part in stock:
- State whether it's a front or rear bumper
Other used Mazda Premacy parts
- Used Mazda Premacy Front Grille
- Used Mazda Premacy Front Bumper
- Used Mazda Premacy Spoiler
- Used Mazda Premacy Bonnet Strut
- Used Mazda Premacy Airbag Control Module
- Used Mazda Premacy Airbag
- Used Mazda Premacy Wheel Hub
- Used Mazda Premacy Suspension Leg
- Used Mazda Premacy Curtain Airbag
- Used Mazda Premacy Track Rod
- Used Mazda Premacy Brake Caliper
- Used Mazda Premacy Window Switch
Used bumper for other Mazda models
Fitment questions
What years does the Mazda Premacy bumper fit?
The Mazda Premacy was sold in the UK across two generations: the first generation ran from 1999 to 2005, and the second generation (also known as the CR-series) ran from 2005 onwards. Bumpers are generation-specific, so always match your car to the correct generation when sourcing a used part. If you are unsure which generation your car belongs to, check your registration with a breaker who can confirm from the VIN.
Will a 2001 Mazda Premacy bumper fit a 2004 Mazda Premacy?
Both the 2001 and 2004 Premacy fall within the first generation (1999–2005), so the bumpers are likely to be from the same platform and should be compatible in principle. However, the first generation did receive a facelift during its run, and bumper designs can change at a facelift even within a generation, so confirm the exact facelift cut-off and whether the specific panel crosses that boundary with your breaker before purchasing.
Will a first generation Mazda Premacy bumper fit a second generation model?
No — the first generation (1999–2005) and the second generation CR-series (2005 onwards) are entirely different platforms, and their bumpers are not interchangeable. Always make sure the part you are sourcing matches your car's generation, and quote your registration to the breaker so they can verify compatibility against the correct vehicle.
Does the trim level affect which bumper I need for my Mazda Premacy?
No — trim level does not affect bumper fitment on the Premacy, as front-end panels are shared across the range within a generation regardless of specification. You may find minor cosmetic differences such as fog light apertures or trim finishes depending on the spec of the donor car, so mention your trim to the breaker so they can match the look as closely as possible. The key things that matter are generation and facelift period, not whether the car is a higher or lower specification.
Do I need to worry about engine size when buying a used Mazda Premacy bumper?
No — engine size has no bearing on bumper fitment for the Mazda Premacy, as the front-end panels are shared across all engine variants within the same generation. Focus on matching the correct generation and facelift period rather than the engine when searching for a used bumper. Quote your registration to the breaker and they will be able to confirm the right part for your car.
How do I know if a Mazda Premacy bumper from a breaker will match my car's lights?
Within each Premacy generation, bumpers are shared across the model range, but headlight and front bumper designs can vary depending on whether your car is a pre-facelift or post-facelift example. If the donor car and your car are both from the same side of a facelift boundary this is less of a concern, but whether a specific bumper crosses a facelift and still fits or looks correct is something you should confirm directly with the breaker against your registration. Mention any differences in headlight type on your car so the breaker can check the bumper apertures match correctly.